AEROPRESS COFFEE MAKER
[CODE NO.3336]
The AeroPress is a device for brewing coffee. It was invented in 2005 by Aerobie president Alan Adler. Coffee is steeped for 10–50 seconds (depending on grind and preferred strength) and then forced through a filter by pressing the plunger through the tube.
The AeroPress uses air pressure, forcing the water through by pushing the plunger down. The AeroPress is a simple device, with a chamber made from tough, heat-resistant plastic It uses a plunger to force water through the coffee, which will be familiar to French pressusers.
The pressurization that occurs in the plunging action is similar to an espresso machine.
This AeroPress brewing system makes coffee by forcing water through coffee under pressure. The result is a concentrated brew of coffee that you can then do different things with. These instructions focus on brewing the coffee and then diluting it with hot water to normal strength.
COST ESTIMATION
Plant Capacity : 1000.00 Nos./day
land & Building (2000 Sq.Mtrs) : Rs. 3.04 Cr
Plant & Machinery : Rs. 3.39 Cr
Working Capital for 4 Months : Rs. 5.71 Cr
Total Capital Investment : Rs. 12.52 Cr
Rate of Return : 58%
Break Even Point : 32%
INTRODUCTION
ADVANTAGES
DISADVANTAGES
CONSTRUCTION
MAIN PARTS
(1) RUBBER PLUNGER END
(2) FILTER CAP
(3) AEROPRESS CHAMBER
(4) PLUNGE
(5) STIR PADDLE
(6) SCOOP
(7) MICRO-FILTERS
WORKING
THE ORIGINAL METHOD
THE UPSIDE-DOWN/REVERSE METHOD
USES AND APPLICATION
B.I.S. SPECIFICATION
MARKET POSITION AND RELEVANT DETAILS
THE PERFECT STARTER KIT
THE BEAUTY OF PERFECT TIMING
KEY TAKEAWAY
AEROPRESS COFFEE MAKER REVIEW
CHART-TOPPING COFFEE MAKERS
MORE OPTIONS TO PICK FROM
IMPORT DATA OF COFFEE BREWING MACHINE
TOTAL VALUE & VOLUME OF IMPORTS IN INDIA
TOP SUPPLIERS
TOP PORTS OF DISCHARGE
MANUFACTURERS/SUPPLIERS OF AERO PRESS COFFEE MAKER
PROCESS FLOW CHART
MANUFACTURING PROCESS
INJECTION MOULDING TECHNIQUE
SCREW PROFILE
MOULDS
WORKING PRINCIPLE
CLAMPING:
INJECTION:
COOLING:
EJECTION:
ADVANTAGES
DISADVANTAGES
QUALITY CONTROL
STEP 1: MACHINE INSPECTION
STEP 2: FINISHING STATION INSPECTION
STEP 3: QUALITY CONTROL DEPARTMENT INSPECTION
PLASTIC INSPECTION SYSTEMS IN INJECTION MOLDING
INJECTION MOLDING DEFECTS
FLOW MARKS
SHORT SHOT
BURN MARKS
FLASH
DISCOLORATION
GAS MARKS (BURNING)
SHORT SHOTS
WELD LINES
FLASH
SINK MARKS
FLOW MARKS
SPLAY
PLANT LAYOUT
SUPPLIERS OF PLANT AND MACHINERIES
INJECTION MOLDING MACHINE
COOLING TOWER
EFFULENT TREATMENT PLANT
AIR POLLUTION CONTROL EQUIPMENTS
AIR CONDITIONING EQUIPMENTS
AIR COMPRESSOR
PLATFORM WEIGHING MACHINE
MATERIAL HANDLING EQUIPMENTS
FIRE FIGHTING EQUIPMENTS
SHOT BLASTING MACHINE
JIGS AND FIXTURE
SUPPLIERS OF RAW MATERIALS
POLY CARBONATE GRANULES
POLY PROPYLENE GRANULES
AEROPRESS FILTER
CARD BOARD
COFFEE POUCH
APPENDIX – A:
1. COST OF PLANT ECONOMICS
2. LAND & BUILDING
3. PLANT AND MACHINERY
4. FIXED CAPITAL INVESTMENT
5. RAW MATERIAL
6. SALARY AND WAGES
7. UTILITIES AND OVERHEADS
8. TOTAL WORKING CAPITAL
9. COST OF PRODUCTION
10. PROFITABILITY ANALYSIS
11. BREAK EVEN POINT
12. RESOURCES OF FINANCE
13. INTEREST CHART
14. DEPRECIATION CHART
15. CASH FLOW STATEMENT
16. PROJECTED BALANCE SHEET